Raspberry Pi Compute Module 3+/32GB Development Kit Type A CM3+ IO Board DS18B20

Description

This auction is for
CM3+ 32GB Package A
Raspberry Pi Compute Module 3+/32GB Development Kit Type A, CM3+ IO Board, DS18B20, IR Remote Controller
Overview
Since the Raspberry Pi Foundation released the Compute Module 3+, you may have been watching it for some time, don't know how to get started. Now it's time to get moving. We prepare this development kit for you to evaluate the Compute Module 3+ quickly, reducing your development cycle.
The key parts in this Compute Module 3+ development kit includes:
Compute Module 3+/32GB:
Raspberry Pi 3 Model B+ industrial version, the Pi in a flexible form factor, with 32GB eMMC Flash
Compute Module IO Board Plus:
Extend kinds of interfaces from CM3+, such as USB, HDMI, just like the regular Pi, to help evaluating
CM3+ Features
Broadcom BCM2837B0
Cortex-A53 (ARMv8) 64-bit SoC (at) 1.2GHz
1GB RAM
eMMC Flash
CM3+/Lite: None, but brings the SD card interface to the Module pins so a user can wire this up to an eMMC or SD card
CM3+/8GB: 8GB
CM3+/16GB: 16GB
CM3+/32GB: 32GB
200PIN SODIMM connector (35U hard gold plating I/O pins)
48 x GPIO
2 x I2C
2 x SPI
2 x UART
2 x SD/SDIO
(1x SD has been used for eMMC Flash on non-Lite variants)
1 x HDMI 1.3a
1 x USB2 HOST/OTG
1 x DPI (parallel RGB display)
1 x NAND(SMI)
1 x 4-lane CSI Camera Interface (up to 1Gbps per lane)
1 x 2-lane CSI Camera Interface (up to 1Gbps per lane)
1 x 4-lane DSI Display Interface (up to 1Gbps per lane)
1 x 2-lane DSI Display Interface (up to 1Gbps per lane)
Compared to CM1, the CM3+ supports more OS, like Windows 10 (the free IOT-specific version from Microsoft)
Compute Module IO Board Plus Features
Compatible with the Compute Module IO Board V3 from the Raspberry Pi Foundation
Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs
Arduino connectivity, also supports Arduino shields
1-WIRE interface, for connecting single-bus devices like DS18B20
4x keys, 4x LEDs, 1x Buzzer, for I/O testing
Onboard USB HUB, allows connecting more USB devices
IR receiver, IR remote control is available
Onboard USB TO UART, for serial debugging
Sensor interface
10-bit ADC, 38KSPS, 11-ch (6-ch for Arduino interface, 5-ch for sensors)
16-bit DAC, 2-ch
Onboard RTC, one of the most common and useful functions
What's on the Compute Module IO Board Plus
Compute Module interface:
for connecting Compute Module (CM3 / CM3L / CM3+ / CM3+L)
Compute Module GPIO header:
breakout all the Compute Module pins
Raspberry Pi GPIO header:
for connecting Raspberry Pi HATs
CSI interface:
camera ports, for connecting Raspberry Pi Camera
DSI interface:
display ports, for connecting Raspberry Pi LCD
HDMI port
USB ports:
for connecting USB devices
USB SLAVE interface:
allows you to burn system image in to Compute Module 3/3+
USB TO UART interface:
for serial debugging
Arduino header:
for connecting Arduino shields
AD/DA input/output screw terminals
1-WIRE interface:
for connecting single-bus devices like DS18B20
Sensor interface
Power port:
5V 2.5A
FE1.1S:
USB HUB chip
12MHz crystal
CP2102:
USB TO UART converter
Micro SD card slot:
insert a Micro SD card with pre-burnt system, to start up Compute Module 3/3+ Lite variant
TLC1543:
AD converter
DAC8552:
16-bit DAC, 2-ch
DS3231:
high-precision RTC chip, I2C interface
RTC battery holder:
supports CR1220 batteries
Voltage regulator:
3.3V / 2.5V / 1.8V
LFN0038K:
IR receiver
Buzzer
Power indicator
ACT indicator:
indicating the Micro SD card status
User LEDs
User Keys
BOOT selection
EN: enable the PC to access SD card/eMMC through USB SLAVE
DIS: the Compute Module will boot from SD card/eMMC
VGx power selection:
config the I/O level
USB HUB enable jumper:
HUB enable and USB SLAVE power selection
ADC/DAC configuration:
config the power supply and reference voltage of ADC/DAC
Peripheral configuration:
config the control pins of UART, user keys, user LEDs, 1-WIRE interface, IR receiver, and buzzer
Arduino AD selection
connect 1 and 2: Arduino A0-A5 as digital control pin
connect 2 and 3: Arduino A0-A5 as AD input
Selection Guide
Item
Description
no CM3+
8GB
16GB
32GB
A
B
A
B
A
B
A
B
Compute Module 3+ 8GB
Raspberry Pi 3 CM3+/8GB variant
√
√
Compute Module 3+ 16GB
Raspberry Pi 3 CM3+/16GB variant
√
√
Compute Module 3+ 32GB
Raspberry Pi 3 CM3+/32GB variant
√
√
Compute Module IO Board Plus
Compute Module IO Board V3 compatible and enhanced solution
√
√
√
√
√
√
√
√
7inch HDMI LCD (C)
7inch HDMI high resolution touch display
√
√
√
√
DS18B20
Temperature sensor
√
√
√
√
√
√
√
√
IR remote controller
Allows IR remote control
√
√
√
√
√
√
√
√
5V 3A Power Adapter
Power Adapter 5V 3A Micro-B USB output
√
√
√
√
√
√
√
√
Package Contains
Compute Module
Compute Module 3+ 32GB x1
1
Accessory Pack
Compute Module IO Board Plus x1
DS18B20 x1
IR remote controller x1
LCD adapter x1
22PIN FFC x1
RPi Zero V1.3 Camera Cable 15cm x1
Power adapter US standard 5V/3A micro x1
USB type A plug to micro B plug cable 120cm x2
Jumper Wire 4-pin to separated pins x2
Jumper Wire 2-pin 2.54-pitch 200mm x2
1
2
3
4
5
6
7
8
9
10